CATParts Direct← Home
Home › Parts Knowledge › CAT 308E Mini Excavator Parts

CAT 308E Mini Excavator Parts - Main Pump, Swing Motor and C3.4 Engine Wear List for UK and Ireland

Short answer: The CAT 308E is the 8 tonne class mini excavator that fills UK and Irish plant hire fleets, utility contracts, drainage work and housing site preparation. The British and Irish duty cycle has three signatures: high utilisation with many different operators per machine, wet and muddy ground for most of the year, and road trailer transport between sites several times a week. The failure order is consistent: hydraulic main pump wear from contaminated oil appears first → swing motor and swing brake noise on a worn ring gear → C3.4 engine blow-by and hard cold starting → pin and bushing play in the quick coupler and bucket linkage → exhaust and muffler corrosion from short cycles and condensation. The four readings that matter are cycle time, swing noise, blow-by, and linkage play. Always send the machine serial number - 308E, 308E2 and 308E2 CR use different pump and engine configurations.
CAT 308E mini excavator hydraulic main pump 296-3867
Hydraulic main pump 296-3867 (PVC80RC14) for CAT 308E mini excavators

Why UK and Irish hire fleets wear pumps and linkages first

Three conditions define the mini excavator duty cycle in Britain and Ireland: many operators per machine, most of them not the owner; wet clay and mud that finds every seal and every pin; and frequent transport, which loads the quick coupler, the blade and the tie-down points. A hire machine rarely gets warm before it is switched off again, which is exactly the pattern that kills engines and exhausts.

The real failure chain is: dirty oil and skipped filters → pump wear and slower cycle → operator pushes harder → oil temperature rises → swing motor and brake noise appear → linkage play develops and the bucket starts to slop. The expensive cost is not the part - it is a hire machine off the rate card during a busy week.

AreaField symptomFirst check (free)Usual fix
Hydraulic pumpSlow cycle, weak travelMeasure relief pressureReplace pump
Swing motorNoise, drift, weak swingListen at swing stop, check brakeReplace motor
C3.4 engineBlow-by, hard cold startCheck breather and compressionOverhaul or replace
PinBucket slop, rattleMeasure radial clearanceReplace pin and bushing
MufflerCorrosion, noise, leaksInspect shell and jointsReplace muffler

Hydraulic pump 296-3867: measure before you swap

296-3867 hydraulic main pump (PVC80RC14) fits CAT 308E class mini excavators. On a hire machine the first complaint is always the same: it feels slow. That can be the pump, the relief valve, or simply a clogged suction strainer.

Three checks before ordering: measure system relief pressure; inspect the suction strainer and return filter for debris; compare cycle times hot and cold. If the machine is only slow when hot, oil condition and cooler airflow are the problem, not the pump. Replace the pump when pressure cannot reach specification and the filter shows metal.

Always fit a new suction strainer and return filter with a new pump, and flush the tank. On hire fleets, a missing strainer is the most common reason a replacement pump fails early.

CAT 308E mini excavator swing motor 467-3079
Swing motor 467-3079 for CAT 308E class mini excavators

Swing motor 467-3079: noise on stopping is the early warning

467-3079 swing motor suits the 308E platform. A healthy swing stops firmly with a short hydraulic cushion. A worn motor or brake clunks, drifts after release, or struggles to hold on a slope.

Test in this order: swing on level ground and listen for a clunk at stop; park on a slope and watch for drift with the lever neutral; check the swing gearbox oil for metal. Drift with engine off points at the brake; drift with engine running points at motor leakage. Checking the gear oil is free and prevents a motor swap that does not fix the noise.

CAT 308E C3.4 engine assembly 342-1219
C3.4 engine assembly 342-1219 for CAT 303.5 to 308E class machines

C3.4 engine 342-1219: short cycles are the real killer

342-1219 C3.4 engine assembly fits CAT 303.5 to 308E class machines. In UK hire work the engine rarely reaches working temperature, so condensation and unburnt fuel dilute the oil and accelerate bore and ring wear.

Judge condition with three free checks: breather blow-by with the engine hot; oil consumption between services; cold start behaviour at 5 degrees. Heavy blow-by plus rising oil use means rings and bores are done - a rebuild or replacement engine decision, not an injector fix.

On hire fleets, cut oil service to 250 hours or annually, whichever comes first, and insist on a proper warm-up cycle. It is cheaper than an engine.

Pin 380-8750 and linkage play

380-8750 pin assembly and bushings in the bucket linkage take the abuse of quick coupler changes and constant bucket swaps. Play here transfers shock into the cylinder rods and the boom nose.

Measure radial clearance with a lever and replace pin and bushing as a pair. Fitting a new pin into a worn bushing brings the noise back within weeks.

CAT 308E muffler 415-9802
Muffler 415-9802 / 4159802 for CAT 308E mini excavators

Muffler 415-9802: corrosion from short cycles

415-9802 muffler fits CAT 308E machines. Short cycles never burn off condensation, so the shell corrodes from the inside and the first symptom is a rattle or a soot streak at a joint.

Inspect the shell and joints each service. A leaking muffler near the engine cover is a fire and fume risk on a machine that works next to operatives - replace it rather than patching it.

Lead time, documents and packing to the UK and Ireland

Stock items ship the same day. Delivery to Manchester, Birmingham, London, Glasgow, Dublin and Cork normally takes 4 to 7 working days by express. Pumps and engines over 30 kg move by air or sea consolidation, with tracking provided.

Hydraulic units ship with ports sealed, machined faces rust protected and photographed before packing. Engines ship on a bolted pallet with a moisture barrier. Before dispatch we send the packing list, actual product photos and a loading video. To quote, send three things only: a photo of the machine serial number, a photo of the old part nameplate, and a note on where it is fitted.

Frequently asked questions about CAT 308E parts

Do 308E and 308E2 use the same hydraulic pump?

Not across all builds. 308E, 308E2 and 308E2 CR use different pump references depending on serial number and market configuration. Send the machine serial number and a photo of the old pump nameplate and we confirm before shipping.

The machine feels slow only when hot - is the pump worn?

Usually not. Slow performance that appears only at high oil temperature points to oil condition, suction strainer blockage or cooler airflow. Measure relief pressure hot and cold, and inspect the strainer before ordering a pump.

Clunk when the swing stops - motor or brake?

Test drift with the engine off and with the engine running. Drift with the engine off points at the swing brake; drift and weakness while running point at motor leakage. Check the swing gearbox oil for metal at the same time.

How do I judge whether the C3.4 needs a rebuild?

Three checks: breather blow-by with the engine hot, oil consumption between services, and cold starting at 5 degrees. Heavy blow-by plus rising oil use means rings and bores are worn, which is an engine decision, not an injector fix.

Send the serial number, get fitment confirmed today

Hydraulic, engine and linkage parts for CAT 308E mini excavators, shipped the same day from stock.

Get a quote and stock check
Scan the QR code to chat on WhatsApp about CAT mini excavator parts

WhatsApp +86 139 2519 9399 · Or click to chat directly: WhatsApp quick quote