CATParts Direct← Home
Home › Knowledge Base › CAT 320D / 336D Wear Parts

CAT 320D / 336D Excavator Wear Parts List: Hydraulic Pump, Undercarriage, Engine Parts Cross-Reference

Short answer: 320D and 336D share very few wear parts. The 320D commonly uses main pumps 397-3680 and 272-6955; the 336D pump is matched by nameplate and serial number. Send the serial plate photo plus the old part and we will confirm fitment and quote the same day.

Cross-reference table: 320D vs 336D

Group320D336DNote
Main hydraulic pump397-3680, 272-6955Matched by pump nameplate (336D / 336D2 split by serial)Displacement, flange and ports differ — never interchangeable
Pilot gear pump126-2016 (320DL / 324D)Matched by serial numberLow pilot pressure shows up as weak, slow controls
High-pressure hosesMatched by hose routing113-6741, 4I-6030Replace on bulging or weeping, before a burst stops the machine
Engine injectors310-9607 (C6.4)C9 engine, separate lookupBlack smoke, misfire, hard cold start
Oil pressure sensors320-3060274-6719, 296-8060A warning is often the sensor, not the oil pump
UndercarriageBy serial number and measurementBy serial number and measurementSee wear limits below before ordering
CAT E320D hydraulic main pump assembly 397-3680, warehouse photo
CAT E320D hydraulic main pump assembly 397-3680 — photographed in our warehouse

Three rules for CAT part number lookup

  1. The dash is optional, the prefix is not. 126-2016 and 1262016 are the same part; searching without the dash normally returns more results. But prefixes such as 7I-8154 and 4I-6030 are part of the number — dropping the letters turns it into a different part.
  2. The suffix decides the part. 320D, 320D2, 320DL and 320D GC do not share the same engine and hydraulic components. Reading the decal on the hood is not enough; the serial plate prefix is what matters.
  3. The old part wins. Pumps, injectors and sensors carry a nameplate or stamped number. That number always beats a catalogue guess, especially on the 336D where pump part numbers split across serial ranges.

Is the pump really failing?

Before spending money on a main pump, run these four checks — they cost almost nothing and they prevent the most common wrong order we see:

  1. Oil level, grade and condition. Milky oil means water ingress; a burnt smell means an overheating history. Both destroy a new pump quickly.
  2. Suction strainer and tank breather. A restriction on the suction side causes cavitation: a whine that rises with engine speed and looks exactly like pump failure.
  3. Standby and relief pressure with a gauge. Incorrect settings mimic a weak pump.
  4. Case drain flow and filter inspection. Excessive drain flow confirms internal leakage; brass-coloured glitter on the filter or magnetic plug means the rotating group is damaged and the machine should be stopped immediately.

If metal has circulated, a pump alone is not the repair: flush the tank and lines and fit new filters, or debris will damage the replacement within hours.

Undercarriage: measure before you buy

Undercarriage parts — track links, carrier rollers, track rollers, idlers and sprockets — are planned replacements, not emergency ones. The decision should be based on measurement, not appearance:

Because these limits are dimensional, we match undercarriage by serial number and measurement rather than by model name. See undercarriage wear limits and undercarriage wear maintenance for the detail before you order.

Engine parts: check the cheap cause first

Two patterns account for most unnecessary engine part orders. First, low oil pressure warnings: replace the 274-6719 oil pressure sensor or 296-8060 and re-test before stripping the engine — sensors fail far more often than oil pumps. Second, smoke and misfire: test the injectors cylinder by cylinder; 310-9607 injectors on the C6.4 are a routine wear item and replacing the whole set is usually cheaper than two rounds of diagnostics.

CAT 274-6719 oil pressure sensor, warehouse photo
Oil pressure sensor 274-6719 for CAT E336D / E330D / E324D — warehouse photo

How to order without getting the wrong part

Three inputs are enough: the machine serial plate photo, the old part photo or stamped number, and the quantity. We confirm fitment, send warehouse photos of the real part (including its nameplate), and quote the same day. Stock ships immediately; ordered items are confirmed against the supplier's production schedule. Pumps, hoses, injectors and sensors can be consolidated into one crate, which is usually the largest single saving on an export order.

Frequently asked questions

Do CAT part numbers need the dash?

No. 126-2016 and 1262016 are the same part written two ways. Searching without the dash usually returns more hits, but prefixes such as 7I-8154 or 4I-6030 must be kept.

Can a 320D pump be used on a 336D?

No. The machines are in different weight and flow classes — pump displacement, flange, port positions and rotation all differ. Match the 336D pump by nameplate and serial number.

How do I know whether I have a 320D, 320D2 or 320DL?

Read the machine serial plate and its prefix, not the hood decal. Different suffixes use different engines and hydraulic components.

What should I send to get a quote?

A photo of the machine serial plate, a photo or stamped number of the old part, and the quantity. We confirm fitment, send warehouse photos and quote the same day.

Need 320D or 336D wear parts?

Send the serial plate and part photo — same-day fitment check and quote.

Request a quote
WhatsApp QR code for instant quote

WhatsApp +86 139 2519 9399 · scan the code, or open WhatsApp chat