CATParts Direct← Home
Home › Parts Knowledge › 320D2 / 336D2 Excavator Parts

CAT 320D2 / 336D2 Excavator Parts - Hydraulic Pump, Injector and Sensor Wear List for India

Short answer: The 320D2 and 336D2 are the backbone 20 and 36 tonne excavators on Indian quarry, road and irrigation projects, running C6.6, C7.1 and C9 platforms. The wear order in Indian conditions is consistent: hydraulic pump internal leakage from heat and contaminated oil, pressure and fuel sensors failing from vibration and moisture, injection pumps and injectors wearing on variable fuel quality, and connecting rod and bearing wear on high hour engines. Check order: relief pressure and case drain, sensor fault codes, fuel pressure and return flow, oil analysis for bearing metal.
CAT 320D2 hydraulic pump 524-8317
Hydraulic main pump 524-8317 for CAT 320D2 excavator

Why Indian 320D2 and 336D2 fleets wear hydraulics and fuel systems together

Indian quarry and irrigation work means high ambient temperature, long shifts, dusty haul roads and fuel of variable quality. The 320D2 and 336D2 handle that combination reasonably well, but two systems always pay the price: the hydraulic circuit, where heat and contamination accelerate pump wear, and the fuel system, where water and particulates attack the injection pump and injectors.

The chain is predictable: dirty fuel and blocked filters, low fuel pressure, the injection pump works harder, injector spray pattern degrades, combustion temperature rises, the engine runs hot, hydraulic oil temperature follows, pump internal leakage increases, cycle times stretch. Fixing only the hydraulic side leaves the root cause in the fuel tank.

AreaSymptom on siteFirst free checkUsual action
Hydraulic pumpSlow cycles, hot oil, low relief pressureRelief pressure and case drain flowReplace pump
Pressure sensorDerate, wrong gauge reading, fault codeLive data against a gaugeReplace sensor
Fuel injection pumpHard start, low power, white smokeFuel pressure and return flowReplace pump
Fuel injectorMisfire, black smoke, high consumptionCut-out test and return flowReplace injector
Connecting rodKnock, low oil pressure, metal in oilOil analysis and bearing inspectionReplace rod and bearings

Pump 524-8317 - test at temperature, not cold

524-8317 hydraulic pump is the main pump assembly for the 320D2 platform. A cold machine can hide a badly worn pump, because cold oil is thick and leakage is low. Always test at operating temperature.

Three readings decide it: relief pressure (cannot be adjusted into range), case drain flow (climbs sharply when hot), and return filter content (bronze or bright metal means the pump and possibly the travel motors are already damaged). If metal is present, flush the circuit and replace filters before fitting the new pump, otherwise the replacement becomes a consumable.

CAT 320D2 oil and fuel pressure sensor 320-3060
Oil and fuel pressure sensor 320-3060 for CAT 320D2 excavator

Sensor 320-3060 - cheap part, expensive misdiagnosis

320-3060 pressure sensor monitors oil and fuel pressure on the 320D2. When it drifts, the ECM does not see an obvious failure: it sees implausible pressure data and derates the engine or the hydraulics. Operators report lost power, and workshops start replacing pumps that are perfectly healthy.

The test takes minutes: compare live data with a mechanical gauge at the same port. A reading that disagrees with the gauge means the sensor is lying. Check the connector for moisture and vibration damage first, because Indian monsoon conditions kill connectors before sensors.

Injection pump 225-0537 and injector 299-9265

225-0537 fuel injection pump serves the C7.1 and C9 engines used in this machine family. Hard starting, low power and white smoke after a filter change that did not fix the problem usually mean the pump is worn from water and fines in the fuel.

299-9265 fuel injector wears on the same fuel quality issue. Test with a cylinder cut-out and a return flow comparison: an injector returning far more fuel than its neighbours is worn. Replace injectors as a set where budget allows, because mixed wear produces uneven combustion and hides the next failure.

Connecting rod 331-0290 - the high hour decision

331-0290 connecting rod is used on the 326D2 and related C7.1 platforms. Rod and bearing wear shows up late: a knock at idle, falling oil pressure, and bearing metal in the oil sample. By the time the knock is audible the crank journal is usually already marked.

On machines past 12,000 hours, oil analysis every 500 hours is the cheapest insurance available. A rising copper and lead trend with stable oil pressure means the bearings are going and the decision should be made before the crank is damaged.

CAT 320D2 connecting rod 331-0290
Connecting rod 331-0290 for CAT 320D2 / 326D2 excavators

Lead time, documents and packing to India

Stock items leave the warehouse the same day. Air freight to Mumbai, Chennai, Delhi, Bengaluru and Hyderabad normally takes 5 to 8 working days. Pumps and engine assemblies travel by sea LCL or FCL into Nhava Sheva, Chennai and Mundra, with schedules confirmed per order. Shipments use fumigation free pallets or wooden cases with machined surfaces protected, and each order ships with a packing list, warehouse photos, a loading video and the commercial invoice and packing list needed for Indian customs clearance.

To quote, we need three things: the machine serial plate photo, the old part nameplate photo and the installation position. With all three we confirm fitment and reserve stock the same day.

Frequently asked questions

Are 320D2 and 336D2 hydraulic pumps interchangeable?

No. They are different displacement pumps on different platforms, and pump configuration also changes within a serial range. Send the machine serial plate and the old pump nameplate so the correct assembly is confirmed before shipment.

Engine derates but no fault is obvious - where do I start?

Compare live sensor data with a mechanical gauge at the same port. A pressure sensor that disagrees with the gauge derates the machine while every mechanical part is healthy. Check the connector for moisture first, then replace the sensor.

Should injectors be replaced one at a time or as a set?

As a set where budget allows, especially on high hour machines running variable fuel quality. Mixed injector wear produces uneven combustion, hides the next failing cylinder and makes diagnosis harder on the second visit.

How long does delivery to India take?

Stock items leave the same day and reach Mumbai, Chennai, Delhi, Bengaluru and Hyderabad in about 5 to 8 working days by air. Pumps and engine assemblies move by sea into Nhava Sheva, Chennai and Mundra, with packing list and loading photos before departure.

Need a quote for 320D2 / 336D2 excavator parts?

Send the machine serial number and old part photos. Fitment confirmed and stock reserved the same day.

Request a quote
WhatsApp QR code

WhatsApp +86 139 2519 9399 · Scan to send a part number, or open the chat