CATParts Direct← Home
Home › Parts Knowledge › 345C / 365C Large Excavator Parts

CAT 345C / 365C Large Excavator Parts - Fuel Pump, Injector, Harness and Idler Wear List for Canada

Short answer: The 345C and 365C are large CAT excavators in Canadian oil sands, forestry road building and northern aggregate production. Canadian duty means extreme cold starts that load batteries, starters and fuel systems, long idle and low-load periods that coke emissions hardware, and remote sites where a missed part costs a full shift. The failure order is consistent: fuel transfer pump pressure drops first → injector wear shows as hard cold starts and white or black smoke → wiring harness and connector corrosion causes false fault codes → undercarriage idlers and rollers wear from frozen, abrasive material. The four readings that matter are fuel supply pressure, cold start quality, fault code frequency, and undercarriage wear. Always send the machine serial number - 345C, 345C L, 365C and 365C L do not share the same pump, injector and harness specifications.
CAT 345C 365C excavator fuel transfer lift pump 1903443
Fuel transfer lift pump 1903443 for CAT C13 and C15 excavator engines

Why Canadian duty stresses fuel systems and wiring

Three conditions define large excavator work across Alberta, British Columbia and the northern territories: cold starts at minus 30 degrees and below; long idle periods that load the emissions system with soot; and remote sites where the nearest parts source can be a full day away. Large excavators in this duty run long hours with limited service windows.

The real failure chain is: cold starts load the battery and starter → fuel supply pressure and filtration become critical → injector wear shows up as hard starts and smoke → extended idling cokes the emissions hardware → moisture and road salt reach connectors and harnesses → false fault codes waste diagnostic hours → undercarriage wears fast on frozen abrasive material. The most expensive cost on a Canadian site is not the part. It is a machine down at a remote location with a crew standing by.

AreaField symptomFirst check (free)Usual fix
Fuel transfer pumpHard start, low supply pressureMeasure supply pressureReplace pump
Fuel injectorSmoke, rough idle, fuel use upCut-out test per cylinderReplace or calibrate
Injector harnessIntermittent misfire, codesWiggle test at connectorReplace harness
Engine harnessMultiple unrelated codesCheck grounds and pinsReplace harness
Guide wheelTrack wander, uneven wearMeasure idler and roller wearReplace idler

Fuel transfer pump 1903443: the cheapest link in the chain

1903443 fuel transfer pump serves CAT C13 and C15 excavator engine platforms. When supply pressure falls, the injection system starves, and the symptoms look like injector failure - hard starting, power loss, and smoke.

Always test supply pressure before ordering injectors. A weak lift pump will make brand new injectors look faulty. This one check saves the most money on cold-climate machines.

Replace it together with the primary filter and water separator. In Canadian winter, water in fuel is the most common cause of supply-side failure.

CAT C13 C15 excavator fuel injector 249-0713 10R-3262
Fuel injector 249-0713 and 10R-3262 for CAT C13 and C15 excavator engines

Injector 249-0713: confirm the cylinder first

249-0713 fuel injector (cross reference 10R-3262) serves CAT C13 and C15 large excavator engines. Rough idle, smoke, higher fuel use and hard cold starts are the classic signs.

Confirm before you buy: run a cut-out test per cylinder and compare return flow. Replace the injector in the failing cylinder, then fix the fuel supply side - drain the tank, renew the water separator - so the new unit is not destroyed by contamination.

Harness 2413150 and 2242896: moisture is the enemy

2413150 C15 injector wiring harness and 2242896 engine main wiring harness serve CAT C15 and 365C class platforms. Corroded pins and cracked insulation produce fault codes that look like sensor or injector failures.

Test in this order: check supply voltage and ground resistance first, open the connectors and look for green corrosion or moisture, do a wiggle test with the engine running. Only after all three pass should you condemn a sensor or injector. On Canadian machines, road salt and condensation make harness faults a top-three cause of repeat codes.

CAT C15 engine injector wiring harness 2413150
C15 engine unit injector external wiring harness 2413150 for CAT C15 platforms
CAT 365C excavator engine main wiring harness 2242896
Engine main outer wiring harness 2242896 for CAT 365C class machines

Guide wheel 248-7256: undercarriage on frozen ground

248-7256 guide wheel is a mining grade chassis part for large CAT excavator undercarriages. Frozen, abrasive material and continuous travel on rough ground shorten idler and roller life sharply.

Measure rather than guess: check idler and roller diameter against wear limits, look for seal leakage at the hub, and watch track tension after a cold soak. Track that is too tight in freezing conditions destroys idlers in a single season.

CAT large excavator guide wheel idler 248-7256
Mining grade guide wheel 248-7256 for large CAT excavator undercarriages

Cold start procedure that saves batteries and starters

Two habits cut cold-climate failures dramatically: use the correct block heater and intake preheat time before cranking, and avoid repeated long cranking - limit each attempt and let the starter cool between attempts. Starters and ring gears fail from heat, not from cold.

Log battery voltage before and during cranking each winter. A battery that drops more than specification under load will take the starter and the ring gear with it.

Lead time, documents and packing to Canada

Stock items ship the same day. Express delivery to Calgary, Edmonton, Vancouver and Toronto normally takes 5 to 8 working days. Heavy units move by sea freight consolidation with the sailing confirmed to Vancouver or Montreal before booking.

Fuel system and engine units are shipped ports sealed, protected against moisture and photographed before packing. Heavy items go on heat-treated-free pallets or in plywood crates. Before dispatch we send the packing list, actual product photos and a loading video. To quote, send three things only: a photo of the machine serial number, a photo of the old part nameplate, and a note on where it is fitted.

Frequently asked questions about 345C / 365C parts

Are the 345C and 365C fuel system parts interchangeable?

Not by model number alone. The 345C, 345C L, 365C and 365C L platforms use different pump, injector and harness specifications that follow the serial number. Send the machine serial number and a photo of the old part nameplate so the correct reference is confirmed before shipping.

Hard cold start - injector or lift pump?

Test supply pressure first. A weak transfer pump starves the injection system and produces symptoms that look exactly like injector failure. Confirm supply pressure before ordering injectors - this check prevents the most common misdiagnosis on cold-climate machines.

Repeated fault codes with no obvious cause?

Suspect the harness. Check supply voltage and ground resistance, open the connectors and look for corrosion or moisture, and do a wiggle test with the engine running. On machines working in salt and condensation, harness faults are a leading cause of repeat codes.

How often should the undercarriage be measured?

Measure idler and roller diameters and check track tension at every 250 hour service, and always after a cold soak. Track that is too tight in freezing conditions destroys idlers quickly, and measurement costs nothing compared with an idler set.

Send the serial number, get fitment confirmed today

Fuel system, wiring and undercarriage parts for CAT 345C and 365C large excavator platforms, shipped the same day from stock.

Get a quote and stock check
Scan the QR code to chat on WhatsApp about CAT large excavator parts

WhatsApp +86 139 2519 9399 · Or click to chat directly: WhatsApp quick quote