CATParts Direct← Home
Home › Parts knowledge › 390D excavator parts

CAT 390D Excavator Parts: Hydraulic Pump, Injector and Swing Gearbox Wear List for South American Copper Mines

Short answer:The CAT 390D is a 90 tonne class hydraulic excavator powered by the C18 engine, a primary loading machine in Chilean and Peruvian copper mines for bench stripping and high-volume truck loading. Four conditions drive its wear: continuous two-shift loading with high cycle counts, fine abrasive ore dust, high altitude that thins combustion air, and long 25 to 40 day freight from China to San Antonio or Callao. The failure order is stable: the main hydraulic pump first (slower cycles, rising oil temperature), then the fuel injectors and C18 combustion hardware (black smoke, rising fuel burn, derate at altitude), then the swing gearbox and distributor valve (swing drift, uneven rotation). The expensive part is never the injector, it is a 90 tonne loader down while a haul truck queue idles at the bench. Quote with the machine serial number and a photo of the old part plate - 390D, 390F and 374D share component families but not every pump flange, injector code and gearbox ratio.
Main hydraulic pump 369-9676 (Imported Hydraulic Pump 369-9676 Suitable for Caterpillar 365D 374D 390D Excavator Engine)
Main hydraulic pump 369-9676 (Imported Hydraulic Pump 369-9676 Suitable for Caterpillar 365D 374D 390D Excavator Engine)

Why the 390D loses pump efficiency before it loses engine power

Copper mine loading is high cycle, high load, dusty, two shifts a day. Fine ore dust enters through a tired breather, thins the oil film and laps the pump port plate and cylinder barrel. The first symptom is usually slower cycle times and oil temperature running ten degrees above the rest of the fleet, not a loss of engine power.

The chain runs like this: breather failure - dust in oil - port plate scoring - internal leakage - oil temperature rise - seal and hose ageing - injector and combustion stress from sustained load. At altitude the margin is thinner, because the engine has less air to work with. A quarterly oil sample is cheaper than one main pump.

AreaSymptom on siteFree first checkUsual fix
Hydraulic pumpSlow cycles, hot oilRead main relief pressure and flowNew pump or rebuild, flush lines
Fuel injectorBlack smoke, high fuel burnCylinder cut test, return flow checkNew or calibrated injector
Swing gearboxSwing drift, uneven rotationCheck brake release and back pressureNew gearbox, refill lube
Distributor valveJerky functions, driftRead pilot pressure at temperatureClean spool or new valve
C18 engine assemblyDerate at altitude, low powerRead boost and intake temperatureOverhaul or new assembly

Hydraulic pump 369-9676 Imported Hydraulic Pump 369-9676 Suitable for Caterpillar 365D 374D 390D Excavator Engine: read pressure and flow before ordering

Order of work matters. Bring the oil to working temperature, fit a gauge at the main relief, compare to rated pressure, then measure flow under load. Pressure is correct but flow is down, that is internal pump leakage; pressure follows engine rpm and never reaches spec, check the regulator and engine first. Pump 369-9676 Imported Hydraulic Pump 369-9676 Suitable for Caterpillar 365D 374D 390D Excavator Engine is used across several large CAT excavators - confirm the flange, the regulator and the port orientation, because two port layouts exist.

When the pump is replaced, change return and suction filters, clean the tank bottom and fit a new breather. A new pump on dusty oil repeats the same failure within two thousand hours.

Diesel fuel injector 211-3024 (Diesel Fuel Injector 211-3024 Suitable for Caterpillar Cat C15/C18 Engine Compatible with)
Diesel fuel injector 211-3024 (Diesel Fuel Injector 211-3024 Suitable for Caterpillar Cat C15/C18 Engine Compatible with)

Fuel injector 211-3024 Diesel Fuel Injector 211-3024 Suitable for Caterpillar Cat C15/C18 Engine Compatible with: cut test and return flow first

Black smoke and rising fuel burn are not a blank cheque for six injectors. Run a cylinder cut test, compare return flow per cylinder and check the diesel filters for water. At high altitude a marginal injector shows up much earlier, so the pattern matters. Injector 211-3024 Diesel Fuel Injector 211-3024 Suitable for Caterpillar Cat C15/C18 Engine Compatible with is a C18 family part - match the injector code and the engine serial number, not just the shape of the body.

After fitting, replace filters, drain tank water, bleed the low pressure circuit fully and clear any derate codes. Skipping the bleed is the most common reason a new injector still reads rough.

Swing gearbox 378-9557 Imported Rotary Tooth Gearbox Reducer 378-9557 Suitable for Caterpillar 390F 385C 390D Exc: brake and back pressure before the gearbox

Swing drift and uneven rotation are usually brake release pressure or back pressure, not a stripped gearbox. Measure brake release pressure and check swing back pressure cold and hot before ordering. Gearbox 378-9557 Imported Rotary Tooth Gearbox Reducer 378-9557 Suitable for Caterpillar 390F 385C 390D Exc is a reduction unit shared across the 390 and 374 families - confirm the ratio and the mounting bolt circle, because the two are not interchangeable.

When the gearbox is replaced, refill with the correct lube spec, inspect the swing ring grease and cycle the swing slowly under no load. A dry swing ring will wear a new gearbox quickly.

Swing gearbox reducer 378-9557 (Imported Rotary Tooth Gearbox Reducer 378-9557 Suitable for Caterpillar 390F 385C 390D Exc)
Swing gearbox reducer 378-9557 (Imported Rotary Tooth Gearbox Reducer 378-9557 Suitable for Caterpillar 390F 385C 390D Exc)

Distributor valve 295-7767 Distributor Valve Assembly 295-7767 295-7745 Suitable for Caterpillar 374 390F 390D 385C E and C18 engine assembly 359-1886 C18 Engine Assembly 359-1886 484-3456 Suitable for Caterpillar 385C, 390D, 390D2, 390F, 39

Jerky functions and drift often come from a sticky spool or low pilot pressure, not a worn valve body. Read pilot pressure at working temperature and cycle each spool by hand before ordering. Valve 295-7767 Distributor Valve Assembly 295-7767 295-7745 Suitable for Caterpillar 374 390F 390D 385C E replacement should include flushing the pilot lines and fresh seals.

Persistent derate at altitude, once cooling, boost and intake temperature are proven good, points to the engine itself. A C18 assembly 359-1886 C18 Engine Assembly 359-1886 484-3456 Suitable for Caterpillar 385C, 390D, 390D2, 390F, 39 is a major decision - confirm the engine serial number, power rating and aftertreatment configuration. A mismatched rating starts fine but derates continuously under load.

Three rules for South American copper mine 390D fleets

1) Quarterly hydraulic oil sample and breather check. Dust is the number one pump killer on a bench. 2) Cut test and return flow before any injector order. Six new injectors rarely fix a two cylinder problem. 3) Full serial number and old part plate photo with every enquiry. Shared component families cause most wrong shipments.

Follow these three and 390D availability stabilises. A mine measures cost per loaded tonne, not the price of one injector.

Common spares and lead time reference

AreaTypical part numberSuggested stockLead time from China
Main hydraulic pump369-96761 per 8 machines15 to 25 days
Diesel fuel injector211-30241 set per 6 machines10 to 18 days
Swing gearbox reducer378-95571 per 10 machines18 to 30 days
Distributor valve295-77671 per 10 machines12 to 20 days
C18 engine assembly359-1886On demand25 to 40 days

To San Antonio, Callao and Antofagasta: injectors, sensors and valves go by air; pumps, gearboxes and engine assemblies are cheaper by sea. Andean winter and port congestion slow inland haulage, so order downtime parts at least six weeks ahead.

Frequently asked questions (390D South American copper mines)

Will a 390D hydraulic pump fit a 374D directly?

Not always. Flange, regulator and port orientation can differ between the two. Send the machine serial number and a photo of the old part plate before we confirm.

Does slow cycle time mean the main pump is worn out?

Not always. Read main relief pressure and flow under load. Pressure correct with low flow points to internal leakage; pressure that never reaches spec points to the regulator or engine.

Should all six injectors be replaced when smoke appears?

Rarely. Run a cylinder cut test and compare return flow per cylinder, and check filters for water. Replace only what the measurement condemns.

Why does a new C18 assembly still derate?

Usually a mismatched power rating or aftertreatment configuration. Confirm engine serial number, rating and aftertreatment spec before the assembly is shipped.

Need 390D pricing and lead time for a South American copper mine?

Send the machine serial number and the part numbers you need. We reply within 24 hours with price, stock and air or sea timing to San Antonio, Callao or Antofagasta.

Check price and stock
WeChat / WhatsApp QR enquiry

WhatsApp +86 139 2519 9399 · Scan to add WhatsApp and send part numbers Send message