
On iron ore and coal operations the 390F is matched to a fixed truck fleet, so a two second loss per cycle is a production number, not a comfort issue. That is why the first symptom of hydraulic wear on these machines is not a leak or a noise but a cycle time that drifts upward against the baseline. By the time an operator complains about slow hydraulics, the pump has usually been losing flow for weeks.
The chain on a dusty Pilbara or Bowen Basin site: cooling package blocks with dust, oil temperature rises, pump internal leakage grows, relief valve works harder, temperature rises further, seals and hoses harden, and the swing and travel circuits take the extra load. Cooling maintenance is not housekeeping on these machines, it is production maintenance.
| Area | Symptom on site | First free check | Usual action |
|---|---|---|---|
| Main pump | Cycle time drift, hot oil, low relief pressure | Baseline cycle test and case drain | Replace pump |
| Swing gearbox | Swing backlash, noise, oil loss | Backlash measurement and gear oil sample | Replace gearbox |
| Fuel injector | Smoke, power loss, high fuel use | Cylinder cut-out and return flow | Replace injector |
| Oil cooler | Oil temperature high, derate | Airflow and fin blockage inspection | Replace cooler or clean core |
| Starter motor | Slow crank, no crank when hot | Cranking current and cable drop test | Replace starter |
627-1304 hydraulic pump is the main pump assembly used on 390F and 395 class machines. Before condemning it, establish a baseline: record cycle time and relief pressure on a healthy sister machine, then compare. A pump that is 10 percent down on flow at operating temperature is already costing production time.
Confirm with case drain flow at temperature and a return filter inspection. Where metal is present, the circuit must be flushed and every filter replaced before fitting new pumps, otherwise the replacement wears out in a few hundred hours. On large excavators this is where most repeat failures originate.

378-9545 swing gearbox (rotary reducer) handles the constant slewing of load and haul duty. On a 390F the swing circuit runs almost continuously, so the gearbox accumulates cycles far faster than the hour meter suggests.
Measure swing backlash at the bucket tip with the machine on level ground, and sample the gear oil. Increasing backlash with bronze or steel particles in the oil means the planetary set is worn. Do not delay: a failing swing gearbox can damage the swing motor and the swing circle, turning a mid cost repair into a major one.
20R-1303 fuel injector serves the C18 engine in the 390F. On continuous 12 hour shifts, injector wear shows as black smoke under load, fuel consumption drifting up and a soft misfire that the ECM masks by trimming.
Test with a cylinder cut-out and a return flow comparison across the bank. Replace the full set on high hour engines, and clean the fuel system at the same time, because contaminated fuel kills a new set quickly. Water in fuel is the single most common cause on remote Australian sites.
346-8044 oil cooler is shared with the 374F platform. When the core blocks externally with dust, oil temperature climbs and the machine derates long before any mechanical fault appears. Clean the stack at every service and pressure test the core when oil temperature stays high after cleaning.
478-9867 starter motor fails from heat soak and dust on these machines. A slow crank when hot, with a good battery, points to the starter rather than the batteries or cables. Check cable voltage drop before replacing, because a corroded cable imitates a failing starter on remote sites.

Stock items leave the warehouse the same day. Air freight to Perth, Brisbane, Melbourne and Sydney normally takes 5 to 8 working days, with onward freight to mine sites arranged by the customer or by our forwarder. Pumps, swing gearboxes and coolers travel by sea LCL or FCL into Fremantle, Brisbane and Melbourne. Shipments use fumigation free pallets or wooden cases with machined surfaces protected, and each order ships with a packing list, warehouse photos, a loading video and the commercial invoice and packing declaration required for Australian biosecurity clearance.
To quote, we need three things: the machine serial plate photo, the old part nameplate photo and the installation position. With all three we confirm fitment and reserve stock the same day.
Use a baseline comparison: record cycle time and relief pressure on a healthy sister machine, then measure the suspect machine at operating temperature and compare case drain flow. A pump down 10 percent on flow with rising case drain is worn, even if it still digs.
Always compare against the specification for the machine serial and measure at the bucket tip on level ground. The trend matters more than a single reading: backlash that increases between services with metal in the gear oil means the gearbox is failing.
On high hour machines, yes. Mixed wear produces uneven combustion and hides the next failing cylinder. Replace the set and clean the fuel system at the same time, because contaminated fuel will damage new injectors quickly.
Stock items leave the same day and reach Perth, Brisbane, Melbourne and Sydney in about 5 to 8 working days by air. Pumps, swing gearboxes and coolers move by sea into Fremantle, Brisbane and Melbourne, with packing list and loading photos before departure.
Send the machine serial number and old part photos. Fitment confirmed and stock reserved the same day.

WhatsApp +86 139 2519 9399 · Scan to send a part number, or open the chat