CATParts Direct← Home
Home › Parts Knowledge › 773E / 775G Truck Parts

CAT 773E / 775G Off-Highway Truck Parts - Hoist Cylinder, Gear Pump and Injector Wear List for Mongolia

Short answer:The CAT 773E and 775G are off-highway mining trucks working in Mongolian copper and coal operations, typically loaded by 988H class loaders or hydraulic excavators. Mongolian duty has three conditions that set the failure pattern: winter temperatures to minus 35 C with cold starts on unheated machines, high altitude where turbochargers run at higher pressure ratio, and fine dry dust in the dry season followed by mud in the wet season. The wear order is consistent: the hoist gear pump loses flow and the body raises slowly, hoist cylinder seals harden and weep, the turbocharger suffers from cold start oil starvation and high altitude load, injectors coke from long idling in cold weather. Field evidence: body raise time, rod oil film, turbo shaft play and boost, injector balance and exhaust haze. Always quote the truck serial number, because 773E, 773F, 775F and 775G use different hoist and engine part groups.
CAT 773E hoist gear pump 2307132
Hoist gear pump 2307132 for Caterpillar 773E off-highway trucks

Why Mongolian winters break the hoist circuit first

Cold is not just a starting problem on a mining truck. At minus 30 C the hydraulic oil in the hoist circuit is thick enough that the gear pump cavitates during the first minutes of operation, and drivers habitually raise the body immediately after start to check the load. That single habit accounts for a large share of hoist pump failures.

The failure chain: cold start with thick oil, gear pump cavitates and scores, flow drops, body raises slowly, driver revs the engine to compensate, oil overheats in the pump, seals harden, hoist cylinders weep, dust enters through the wiper, rod scores, and the truck goes to the workshop for a cylinder that was damaged by a pump. Add altitude and the engine side joins in: the turbo works harder, exhaust temperature rises, and injectors coke from long idling.

ItemSymptom on siteFree first checkUsual action
Hoist gear pumpSlow raise, whine when coldTime raise cold vs warmReplace pump
Hoist cylinderRod oil film, body creeps downWipe rod, recheck after a shiftReseal or replace
775G cylinderUneven raise, driftCompare both sides raise timeReseal or replace
TurbochargerLow boost, blue haze, whistleCheck shaft play and boostReplace turbo
InjectorHaze at idle, poor balanceCut-out test, read balanceReplace injector

Hoist gear pump 2307132: cold start is the killer

2307132 hoist gear pump is the pump that raises the body on the 773E. It is a small gear pump that runs only during hoisting, which makes it easy to ignore until the body takes 25 seconds to come up instead of 12.

Diagnosis without instruments: time a full raise from idle, cold, and again after a shift when oil is warm. A large difference between the two points to internal wear plus cold oil, and the fix is both a pump and a change of oil grade. Then check suction strainer and breather: in Mongolian dust, a partially blocked strainer produces the same symptom as a worn pump.

Cold climate rules that actually prevent repeat failure: idle for warm-up before hoisting, use the correct low temperature oil grade, and never raise a loaded body on the first minute after start. New pumps that fail in the first month on Mongolian sites are almost always cold start casualties, not quality problems.

CAT 773E hoist cylinder 296-0736 350-3843
Hoist cylinder 296-0736 / 350-3843 for Caterpillar 773E mining trucks

Hoist cylinder 296-0736: reseal or replace

296-0736 hoist cylinder (alternate 350-3843) is the two stage hoist cylinder on the 773E. In cold climates the rod seal hardens and loses elasticity, then dust sticks to the oil film and scores the rod on the next stroke.

Decision rule: if the rod is smooth and only the seal weeps, reseal. If the rod shows scoring, pitting or blue heat marks, replace the cylinder. Resealing a scored rod guarantees a repeat leak within weeks, and on a mining truck that means another full day in the workshop.

Keep the wiper and the rod guard in good condition. They are cheap, and they are the parts that decide whether the expensive cylinder survives the winter.

CAT 775G hoist cylinder 334-8695 417-3726
Hoist cylinder 334-8695 / 417-3726 for Caterpillar 775G off-highway trucks

775G cylinder 334-8695: the second generation change

334-8695 hoist cylinder (alternate 417-3726) is used on the 775G. The 775G body is heavier and the hoist circuit runs higher pressure than the 773E, so seal life is shorter if the pump is not delivering properly.

When one side raises slower than the other, resist the temptation to replace the cylinder. Compare raise time on both sides from the same start position, then check the hoist control valve and the pump flow. Uneven raise with equal cylinder condition is a valve or pump problem, and replacing a cylinder will not change it.

Always replace cylinder seals as a complete kit including the wiper, the buffer and the guide ring. Mixing old and new seals in one cylinder is the most common cause of a leak that returns in the first month.

CAT 775G turbocharger 417-7579
Turbocharger 417-7579 for Caterpillar 775G off-highway trucks

Turbo 417-7579 and injector 232-1183: altitude and cold idling

417-7579 turbocharger suits the 775G. Mongolian mines sit at 1,300 to 1,700 metres, where the turbo runs at a higher pressure ratio to make the same power. That means higher exhaust temperature and less margin when the air filter is dirty.

Check three things: shaft play by hand with the intake hose off, boost pressure against specification, and oil supply line condition. A restricted oil feed from cold start coking destroys bearings before any wear limit is reached. Replace the feed line with the turbo, every time.

232-1183 fuel injector is used on 3408 and 3412E engines in 773E class trucks. In Mongolian winter, long idling to keep the cab warm cokes injector tips and causes rough running, white haze and poor fuel balance. The cure is not only new injectors: fit a cab heater or an engine preheater and cut idling hours, otherwise the new set will coke the same way next winter.

Lead time and logistics into Mongolia

We ship from Guangzhou by air to Ulaanbaatar in 6 to 9 days, or by rail and road through Erenhot in 18 to 28 days depending on border queues. For mine sites in the Gobi, the practical route is air to Ulaanbaatar plus domestic truck, so plan critical spares before the winter road freeze.

A sensible stock package for a fleet of five trucks is: two hoist gear pumps, four hoist cylinder seal kits, one turbocharger, one set of injectors and a full set of hoist hoses. Winter in Mongolia is not the season to discover a missing seal kit.

Send truck serial number, photo of the old part nameplate and the symptom. 773E, 773F, 775F and 775G overlap heavily in the field and the hoist groups are not interchangeable, so the serial number is not optional.

Supply note: we supply aftermarket parts suitable for Caterpillar equipment, not genuine CAT parts. Part numbers are used for cross reference and identification only. Confirm against the truck serial number and the old part nameplate before ordering.

Frequently asked questions about CAT 773E and 775G parts

Will a 773E hoist cylinder fit a 775G?

No. The 775G uses a different hoist cylinder group with higher pressure rating and different mounting. Always confirm with the truck serial number and the old part nameplate before ordering.

Why does the body raise slowly only in cold weather?

Cold oil raises viscosity and a worn gear pump loses flow immediately. Time the raise cold and warm. A large difference means pump wear plus the wrong oil grade, and both need to be corrected.

Can I reseal a scored hoist cylinder rod?

No. Scoring or pitting on the rod will destroy a new seal within weeks. Reseal only when the rod is smooth and the leak is at the seal. Otherwise replace the cylinder.

What causes white haze and rough idle in winter?

Usually coked injectors from long idling to keep the cab warm, made worse by altitude. Replace the injectors and cut idling hours by fitting a cab heater or engine preheater, otherwise the fault returns.

Send the serial number, get fitment confirmed today

Aftermarket hoist, hydraulic and engine parts for CAT 773E / 775G mining trucks, in stock and shipped from Guangzhou.

Get price and stock
Scan the QR code to ask about CAT mining truck parts on WhatsApp

WhatsApp +86 139 2519 9399 · Or message us directly: Chat on WhatsApp