CATParts Direct← Home
Home › Parts Knowledge › 950G / 962G Loader Parts

CAT 950G / 962G Wheel Loader Parts - Pump, Injector and Bucket Wear List for Peru and Bolivia

Short answer:The CAT 950G and 962G are 17 and 19 tonne wheel loaders, the workhorses of Peruvian and Bolivian mine yards, aggregate plants and high altitude port operations. Four hard conditions define the market: altitude of 3000 to 4500 metres that costs naturally aspirated engines a fifth of their power, abrasive Andean ore and aggregate, dry season dust followed by wet season mud, and parts moving into Lima, Arequipa or Arica in 10 to 18 days. Failure order is consistent: fuel injectors and transfer pump wear first, showing as black smoke and high consumption, then hydraulic pump pressure falls and lift slows, then bucket teeth and edge wear out on ore. Always quote the machine serial number - 950G and 950G Series II differ in engine and hydraulic arrangement.
Hydraulic pump 127-8218 (127-8218 Diesel Fuel Injector 3116 3126 Engine Suitable for ) for CAT 950G / 962G wheel loader
Hydraulic pump 127-8218 (127-8218 Diesel Fuel Injector 3116 3126 Engine Suitable for ) for CAT 950G / 962G wheel loader

Altitude sets the failure order on the Altiplano

At 4000 metres the air is roughly 60 percent of sea level density. An older engine already at its limit burns richer, carbons up faster and runs hotter exhaust. Combine that with abrasive Andean ore in the bucket and long shifts, and the sequence is fixed: fuel system first, hydraulics second, ground engaging tools third.

The mechanism is a loop: worn injectors spray poorly, fuel burns late, power drops, the operator compensates with throttle, hydraulic oil temperature rises, hot oil thins and the pump loses volumetric efficiency, lift slows, the operator crowds the pile harder, and the teeth and edge finish the cycle.

AreaSymptom on siteFirst check (no cost)Usual action
Fuel injectorBlack smoke, hard start, high fuel useExhaust colour, fuel pressure testReplace injectors as a set
Hydraulic pumpSlow lift, hot oil, whineMeasure main and pilot pressureReplace pump, flush circuit
Bucket teeth / edgePoor penetration, worn floorMeasure tooth length, edge heightReplace teeth, reverse edge
TurbochargerSmoke, whistle, slow responseShaft play check at serviceRebuild or replace
Cooling packageOverheat on loadLight test through coreClean or replace core

Injectors 1957336 Engine Wiring Harness 195-7336 1957336 Suitable for CAT 322 - replace the set, not one unit

At altitude, injector wear is not optional - it is the schedule. On a high hour 950G or 962G, replacing a single injector is false economy because the rest are at the same wear stage and the next failure follows within weeks. Replace the set, clean the fuel tank and change both filters in one job.

Diagnose before spending: black smoke under load, hard cold starts, fuel consumption up more than 10 percent, and a misfire that clears warm. Two or more of these point to injectors. Check the transfer pump and the return line restriction at the same time - a weak transfer pump mimics injector failure.

At altitude also check the air filter restriction every service. Thin air already costs power; a restricted filter costs more.

Fuel injector 1957336 (Engine Wiring Harness 195-7336 1957336  Suitable for CAT 322) for CAT 950G / 962G engine
Fuel injector 1957336 (Engine Wiring Harness 195-7336 1957336 Suitable for CAT 322) for CAT 950G / 962G engine

Hydraulic pump 127-8218 127-8218 Diesel Fuel Injector 3116 3126 Engine Suitable for - pressure first, parts later

Measure main relief pressure at working temperature, then pilot pressure, then flow. Pressure at specification with falling flow means pump wear; pressure below specification means relief valve or pump control; low pilot pressure means check the pilot circuit and filters first.

When the pump is replaced, flush the circuit, replace every filter, clean the reservoir and fit a new breather. Altiplano dust through a tired breather is the most common reason a new pump fails early in this region.

Bucket teeth and edge 162-9612 Fuel Transfer Pump 162-9612 Suitable for Cat 950G 938G 962G - ore wear rates

Andean ore and crushed granite is significantly more abrasive than limestone. Practical regional numbers: an edge that lasts 800 hours in limestone lasts 400 to 550 hours in ore feed. Measure tooth length and edge height every 250 hours.

Replace teeth before the adapters wear round - a worn adapter cannot hold a new tooth and costs several times a tooth. Flip a reversible edge at half wear to recover 30 to 40 percent of its life.

Bucket tooth and adapter 162-9612 (Fuel Transfer Pump 162-9612 Suitable for Cat 950G 938G 962G ) for CAT 950G / 962G loader
Bucket tooth and adapter 162-9612 (Fuel Transfer Pump 162-9612 Suitable for Cat 950G 938G 962G ) for CAT 950G / 962G loader

Turbocharger 191-2942 191-2942 Construction Machinery Parts Hydraulic Fan Pump Sui - the altitude multiplier

At altitude the turbo works hardest of all the engine components, and its wear shows as smoke, a change in whistle note and slow response. Check shaft play at every service - play beyond the limit means a rebuild before the shaft lets go and feeds the engine its own fragments.

After any turbo replacement, find the cause before start up: a clogged air filter or an oil starvation problem will kill the new unit at the same hour mark. Check the air intake restriction and the oil feed line on the same job.

Cooling and planning 8X-9255 CAT 962G 950G Hydraulic Hose Assembly 8X-9255 for Engine - dry season dust, wet season mud

The dry season on the Altiplano brings fine mineral dust; the wet season brings mud that packs the core. Clean the package every 250 hours from the inside out at low pressure, and inspect the core for the corrosion that high altitude UV and thermal cycling accelerate.

Plan the stock list per machine and order against wear trends. Sea freight into Callao works for edges, cores and teeth; air freight for injectors, pumps and turbos when a machine is down. Bolivia usually routes via Arica or Iquique, so add the overland leg to the plan.

Common parts and lead times

AreaTypical part numberSensible stockLead time from China
Hydraulic pump127-82181 per 6 machines12 to 18 days by air
Fuel injector19573361 engine set per machine7 to 12 days
Bucket tooth162-96121 set per machine10 to 20 days
Turbocharger191-29421 per 8 machines10 to 18 days
Cooling core8X-92551 per 10 machines15 to 25 days

FAQ - 950G / 962G in Peru and Bolivia

Are 950G and 962G injectors interchangeable?

No. The engine ratings and injector settings differ between the two models, and Series II machines differ again. Confirm by serial number and by the number stamped on the old injector.

Why is fuel consumption so high at altitude?

Thin air makes the engine run rich, and worn injectors make it worse. Replace the injector set, check the transfer pump and the air filter restriction together - all three interact at altitude.

Is slow lift always the hydraulic pump?

No. Measure main and pilot pressure at working temperature first. A clogged suction screen or a tired relief valve mimics pump wear at a fraction of the replacement cost.

When should the turbocharger be rebuilt?

When measured shaft play exceeds the limit, or when the whistle note changes with smoke. Rebuild before failure - a failed turbo feeds debris into the engine and multiplies the repair cost.

Need a quote and lead time for 950G / 962G parts?

Send the machine serial number and part numbers. We reply within 24 hours with price, stock and air or sea transit time to Lima, Arequipa or Arica.

Check price and stock
Scan to enquire on WhatsApp

WhatsApp +86 139 2519 9399 · Scan and send part numbers directly on WhatsApp Send a message