CATParts Direct← Home
Home › Parts Knowledge › 950M / 962M Loader Parts

CAT 950M / 962M Wheel Loader Parts — Hydraulic Pump, Spline, Bearing and Wheel Hub Wear List for Australian and New Zealand Fleets

Quick answer:On 950M and 962M loaders running Australian mining load-out, quarry face work and New Zealand forestry and port handling, the wear order is consistent: hydraulic pump and axle splines first (high fill buckets and long haul ramps), then wheel bearings and hub assemblies (continuous loaded travel), then linkage bushings. Pump symptoms often trace back elsewhere, so measure pilot pressure and case drain before quoting a pump.
CAT hydraulic pump 419-8920 for 950K 950M 962K 962M wheel loaders
Hydraulic pump 419-8920 for CAT 950K, 950M, 962K and 962M wheel loaders

Why Oceania duty produces a distinctive 950M / 962M wear pattern

Australian loaders often work mine load-out and hard rock quarry faces where buckets are consistently filled to maximum and haul distances are measured in hundreds of metres. New Zealand applications skew toward forestry residues, port handling and agricultural bulk, with more moderate cycles but far wetter, more corrosive conditions.

Both environments load the machine in the same two places: the work hydraulics, because every cycle raises the bucket under full load, and the driveline, because ramps and long hauls put continuous torque through axles and hubs.

SystemTypical symptomFirst field checkUsual fix
Hydraulic pumpSlow lift, weak breakout, heatMeasure case drain flow and pilot pressurePump repair or replacement
Axle splineShuttle shock, metallic clunk on reversalCheck spline lash at the shaftSpline shaft replacement
Wheel bearingsHub heat, growl under load, playMeasure hub temperature and end playBearing set replacement
Wheel hubWheel movement, oil at the hub faceInspect seal lips and fastenersHub assembly service
Linkage bushingsLoose linkage, uneven bucket motionMeasure pin to bore clearanceBushing and pin set

Hydraulic pump 419-8920: confirm the control definition

419-8920 hydraulic pump is used on the 950K, 950M, 962K and 962M loader range. Although the platforms are close, displacement and control definitions shift across serial prefixes, so we always confirm the machine serial and the pump nameplate before release.

Two measurements decide whether the pump is actually at fault: case drain flow at operating temperature and pilot pressure. High case drain with correct pilot pressure means the pump is genuinely worn. If pilot pressure is also low, the fault may sit further upstream in the control circuit.

Axle spline 396-3892: the source of most shuttle complaints

When a loader clunks on direction change, operators often suspect the transmission. In practice the wear frequently sits in the axle spline. Checking lash at the shaft before stripping anything costs very little and prevents the most expensive possible misdiagnosis.

We supply 396-3892 spline shaft for 950M and 962M machines, alongside 8B-6343 tapered bearing which many fleets replace at the same time. Inspecting the mating bore during this work avoids a second teardown.

CAT axle spline shaft 396-3892 for 950M 962M wheel loaders
Spline shaft 396-3892 for CAT 950M and 962M wheel loaders

Bearing 8B-6343 and hub 525-8085: loaded travel costs

Long loaded hauls and ramps turn wheel bearings into scheduled consumables. The practical monitoring method across an Oceania fleet is simple: take hub temperature readings after loaded runs and treat any hub running notably hotter than its opposite side as a pending failure.

We ship 8B-6343 bearing and the 525-8085 hub assembly (with 373-4070 as the sibling number) for 950M machines. Replace seals at every hub opening — reusing tired seals is the fastest way to repeat the whole job.

Bushing 7P-3194 and linkage wear

Linkage wear is easy to underestimate because it develops slowly. The standard check is pin-to-bore clearance at every service. Deep-reaching repairs start when a loose pin begins to oval its bore, which is why routine bushing replacement pays for itself.

We keep 7P-3194 bushing in stock for 986H, 950M and 930K applications. As always, pins and bushings should be renewed together rather than one at a time.

Lead time, packing and documentation to Australia and New Zealand

Stock items ship the same day; international express typically reaches Sydney, Melbourne, Brisbane, Perth and Auckland in 6 to 11 working days. Heavy assemblies including complete hubs and pumps travel by sea, consolidated or full container, with transit confirmed against the destination port. Cargo ships in wooden cases or heat-treated pallets with a packing list and loading photos provided before dispatch.

Sending the machine serial prefix, the old part number and the mounting position is enough for us to confirm fitment the same day.

Frequently asked questions

Are 950M and 962M hydraulics and driveline parts interchangeable?

Several are shared, including pump 419-8920 across the 950K/950M/962K/962M range and spline 396-3892 across 950M and 962M. Confirm against the machine serial prefix before ordering, since displacement and control definitions shift between prefixes.

The loader clunks when changing direction. Transmission or axle?

Check axle spline lash first. Worn splines produce the same shuttle clunk as transmission trouble but cost far less to repair. Only strip the transmission once the spline lash is confirmed within specification.

How do I monitor wheel bearing condition across a fleet?

Take hub temperature readings after loaded runs and compare left to right. A hub running clearly hotter than its opposite side is a pending failure, and replacing bearing 8B-6343 before play develops prevents hub damage.

How long does delivery take to Australia or New Zealand?

Stock items ship the same day, usually arriving in 6 to 11 working days to Sydney, Melbourne, Brisbane, Perth and Auckland. Heavy assemblies go by sea, consolidated or full container, with transit confirmed against the destination port.

Need 950M / 962M loader parts pricing?

Send the machine serial prefix and the old part number — we confirm fitment and reserve stock the same day.

Request a quote
WhatsApp QR for parts enquiry

WhatsApp +86 139 2519 9399 · Scan to send your part number, oropen the chat directly