CATParts Direct← Home
Home › Parts Knowledge › CAT 980H Loader Parts

CAT 980H Wheel Loader Parts - Hydraulic Pump, Torque Converter and Bucket Wear List for Romania and Bulgaria

Short answer:The CAT 980H is a 30 tonne class wheel loader working in Romania and Bulgaria in aggregate quarries, cement plants, port grain and bulk terminals, and highway subgrade projects. The market has four defining conditions: winter down to minus 20 degrees, salt and brine on yard roads, abrasive crushed stone, and buyers who compare every quote against EU dealers. The failure order: hydraulic pump loses pressure and the loader feels slow, then torque converter and transmission run hot and shift harshly, then bucket edge and teeth wear through. Because the 980H is out of production, aftermarket quality varies widely, so confirm by serial number and the nameplate on the old part.
Hydraulic pump 250-1305 (250-1305 Diesel Fuel Injector for Caterpillar 3500B Engine 3) for CAT 980H wheel loader
Hydraulic pump 250-1305 (250-1305 Diesel Fuel Injector for Caterpillar 3500B Engine 3) for CAT 980H wheel loader

Eastern European yards: cold start, salt, abrasive stone

Romanian and Bulgarian quarries and port terminals run the machine hard in temperatures that swing from minus 20 to plus 35 degrees. Cold starts with summer oil, salt on the yard roads and crushed stone with high quartz content combine into a specific wear pattern.

Failure chain: cold start with thick oil, suction restriction, pump wear on the first minutes of every shift; salt and brine attack the bucket, pins and brake pistons; abrasive stone wears the edge and teeth faster than limestone. Add long shifts with rented operators and you get a machine that is always one component behind on maintenance.

AreaSymptomFirst check (no cost)Usual action
Hydraulic pumpSlow lift, hot oilMain and pilot pressure testReplace pump, flush
Torque converterPoor push, high oil temperatureStall test, oil colourRepair converter or replace
Bucket edge and teethPoor penetration, worn baseMeasure edge height and tooth lengthReplace edge, teeth or adapter
Brake pistonsDrag, uneven brakingCheck for corrosion and seal weepReplace pistons and seals

Hydraulic pump 250-1305 250-1305 Diesel Fuel Injector for Caterpillar 3500B Engine 3 - the three step test

Before replacing the pump on a 980H, run the three step test. Step one: pilot pressure. If it is out of specification, fix the pilot circuit first. Step two: main pressure and flow at relief. Pressure that will not reach specification with flow dropping together means the pump is worn. Step three: filter cut and oil sample. Bronze means piston and barrel wear, steel means gears or bearings.

Cold climate note: use the correct viscosity grade for the season and warm the machine at idle before loading it. Most of the pump wear we see from this region happens in the first ten minutes of a winter shift, not at full load in summer.

Torque converter and transmission parts 618-0750 (618-0750 Diesel Fuel Injector Suitable for CAT 618-0750 for ) for CAT 980H
Torque converter and transmission parts 618-0750 (618-0750 Diesel Fuel Injector Suitable for CAT 618-0750 for ) for CAT 980H

Torque converter 618-0750 618-0750 Diesel Fuel Injector Suitable for CAT 618-0750 for - stall test before repair

A 980H that will not push and runs hot is often diagnosed as a converter failure when the real cause is a restricted oil circuit or a worn pump drive. Run a stall test and compare with specification: low stall speed points to the engine or converter, high stall speed to the transmission side.

Also check oil level, colour and filter cut, and confirm the cooler is clean. A plugged cooler raises temperature until the converter seals harden and leak. In this region the cheapest reliability gain is a disciplined cooler cleaning schedule.

Bucket 2556805 Suitable for Caterpillar 980H WHEEL LOADER Gp-Ps- Hydraulic and teeth 3520206 Excavator Water Pump 352-0206 C11 C13 Engine Parts Water Pum - cost per tonne in crushed stone

Crushed granite and river gravel in Romania and Bulgaria wear an edge far faster than limestone. Expect roughly half the life you would get in a soft stone yard. Measure edge height and tooth length every 250 hours and plan replacements by tonnes handled rather than by calendar.

Flipping the edge at half wear adds 30 to 40 percent of life. Replace teeth before the adapter shoulders round off, otherwise a low cost wear item becomes a welding and downtime job.

Winter preparation checklist

Four items that cost little and prevent most winter failures: correct oil viscosity for the season, block heater or preheat before start, grease every pin daily in salt conditions, and wash the yard salt off the bucket linkage and brake area weekly. Salt left on brake pistons is the most common cause of drag and uneven braking we see from this market.

Buying aftermarket for an out of production model

The 980H is out of production, so genuine supply is limited and aftermarket quality varies. Judge a supplier on three things: material and heat treatment documentation, machining accuracy on mating surfaces, and whether test data is provided for pumps and converters. The cheapest quote is usually the most expensive decision when the machine stops a second time.

Quotes are confirmed by serial number and part number together. See the quote page for price and delivery to Romania and Bulgaria.

FAQ - CAT 980H in Romania and Bulgaria

How do I confirm the right pump for a 980H?

Use the machine serial number together with the nameplate on the old pump. Several build configurations exist and the pressure settings differ, so a part number alone is not enough.

What does a stall test tell me?

It separates an engine or converter problem from a transmission problem. Low stall speed points upstream, high stall speed points to the transmission. Always compare with the specification for your serial number range.

Why do brakes drag in winter?

Salt and brine corrode the brake pistons and harden the seals. Wash the area weekly in winter and replace corroded pistons rather than only the seals.

Do you supply to Romania and Bulgaria?

Yes. Air freight from China takes 5 to 10 days and sea freight 30 to 40 days. Provide the serial number and part numbers and we confirm configuration before shipping.

Need a 980H quote for Romania or Bulgaria?

Send the machine serial number and part numbers. We reply within 24 hours with price, stock and freight timing.

Check price and stock
Scan to chat on WhatsApp

WhatsApp +86 139 2519 9399 · Scan the QR code and send part numbers on WhatsApp Send a message