CATParts Direct← Home
Home › Parts Knowledge › 988H Wheel Loader Parts

CAT 988H Wheel Loader Parts - Main Pump, Bucket and Cylinder Wear List for Indonesia Nickel Mines

Short answer:The CAT 988H is a large wheel loader used in Indonesian nickel laterite mines in Sulawesi and Halmahera to load 773 and 775 class trucks from stockpiles. Nickel laterite duty has three traits that matter more than tonnage: wet sticky ore that packs into the bucket and sticks to the bowl, year round humidity with heavy tropical rain, and continuous three shift operation with no dry season break. The wear order is consistent: the main hydraulic pump loses flow and the lift gets slow when hot, the bucket edge and bowl wear plate wear through and ore packs behind them, lift and tilt cylinder seals weep under side load, the oil cooler clogs with laterite fines and oil temperature climbs. Field evidence to read: lift cycle time hot, bucket edge thickness, rod oil film, cooler fin condition. Always quote the machine serial number, because 988G, 988H and 988K use different pump and bucket part families.
CAT 988H hydraulic main pump 216-8978 385-0022
Main hydraulic pump 216-8978 / 385-0022 for Caterpillar 988H wheel loaders

Why nickel laterite destroys loaders differently

Nickel laterite is not abrasive like granite. It is wet, sticky and heavy, and that changes the failure pattern. A bucket that does not empty cleanly means the operator shakes it, which sends shock loads through the tilt circuit every cycle. Ore packed behind the edge means the cutting edge stops cutting and starts bulldozing.

The real failure chain: wet ore packs in the bowl, the operator shakes the bucket to empty it, tilt cylinder seals take repeated pressure spikes, the rod seal weeps, dust and water enter the hydraulic oil, the main pump wears, lift slows when hot, the operator raises engine speed, oil temperature climbs further, the cooler clogs with fines, and the machine loses a shift. In Sulawesi the ore also carries high moisture all year, so water contamination in the hydraulic tank is a constant, not an exception.

ItemSymptom on siteFree first checkUsual action
Main pumpSlow lift when hot, weak breakoutTime lift cycle cold vs hotReplace pump
BucketOre packs behind edge, poor fillMeasure edge thickness and bowl wearReplace bucket or rebuild
Lift / tilt cylinderRod oil film, drift under loadWipe rod, recheck after a shiftReseal or replace
Oil coolerOil temperature high, fan loadedInspect fins from the engine sideClean or replace
BearingGrowl at the linkage, heatTouch housings after a shiftReplace bearing

Main pump 216-8978 / 385-0022: the hot oil test

216-8978 main pump (complete pump 385-0022) is the load sensing main pump on the 988H. On laterite sites the first complaint is always slow lift after four hours, because cold oil still has enough viscosity for a worn pump to look healthy.

So test it hot. Time a full raise at operating temperature from the same bucket load and compare with the cold figure. A difference of more than twenty percent means volumetric efficiency has fallen. Then measure case drain flow, and cut the return filter to look for bronze. All three together give a clear verdict, and they cost nothing.

When replacing the pump, flush the circuit, replace the suction strainer and the return filter, and check the tank for water. In Indonesia, a pump replaced without draining water from the tank will fail again within months, and the customer will assume the part was poor quality.

CAT 988H bucket 333-0911 310-9200
Bucket 333-0911 / 310-9200 for Caterpillar 988H / 988G wheel loaders

Bucket 333-0911 / 310-9200: fill factor is the real cost

333-0911 bucket (alternate 310-9200) fits 988H and 988G loaders. On sticky laterite the bucket wears in a place that granite never touches: the bowl and the area behind the cutting edge, because ore packs there and grinds against the plate every cycle.

Measure three things monthly: cutting edge thickness, bowl plate thickness, and whether ore stays in the bucket after dumping. When ore stays behind, the effective capacity drops and the truck count per shift goes up. That is a measurable cost, and it usually appears before the plate actually cracks.

Options are rebuild with wear plate or replace the bucket. Rebuild is cheaper but only if the parent metal is sound. Check for cracks at the corner welds first: welding new plate onto a cracked corner just moves the crack.

CAT 988H lift cylinder 259-4733 1338173
Hydraulic cylinder 259-4733 / 1338173 for Caterpillar 988H / 988G wheel loaders

Cylinder 259-4733: the seal that fails because of shaking

259-4733 hydraulic cylinder (alternate 1338173) is the lift and tilt cylinder family on the 988H. On laterite sites these fail from pressure spikes caused by shaking a sticky bucket, not from hours.

Two step diagnosis. Wipe the rod completely dry, cycle ten times, look again. A damp film is a leak. Then park with a loaded bucket raised and watch drift. External film means the rod seal, drift without external oil means the piston seal.

Fix the cause as well as the part: an anti stick coating or a polished liner in the bucket reduces ore packing, which removes the shaking that destroys the seals. Operators accept this quickly because it also shortens cycle time.

CAT 988H radiator oil cooler 204-2640
Radiator oil cooler 204-2640 for Caterpillar 988G / 988H wheel loaders

Oil cooler 204-2640 and bearing 5P-9769: heat and linkage

204-2640 radiator oil cooler fits 988G and 988H loaders. Laterite fines mixed with rain form a paste that sets on the fins like cement. Once that happens, air flow drops and oil temperature climbs even at night.

Clean it with low pressure water and a soft brush from the engine side, never with a high pressure jet from the front. If the core has already been folded or the seam is weeping, replace it. On Indonesian sites we recommend cleaning every 250 hours during the wet season, because the paste sets faster than most maintenance schedules assume.

5P-9769 bearing is used in the 988H and 988K linkage. Linkage bearings fail quietly: a slight growl at full raise, then heat at the housing, then play that shows up as a bucket that will not hold a level cut. Grease every shift and feel the housings after work; that is the whole inspection.

Lead time, packing and how to order into Indonesia

We ship from Guangzhou to Jakarta, Surabaya and Makassar by air in 5 to 8 days, or by sea to Tanjung Priok and Makassar in 18 to 25 days. For remote Sulawesi sites the practical route is air to Makassar plus domestic forwarding, so plan consumables two months ahead.

A sensible stock package for one 988H on three shifts is: one main pump, one set of cylinder seal kits, one oil cooler, one linkage bearing set, and a spare cutting edge.

Send machine serial number, photo of the old part nameplate and the symptom. Serial number matters here because 988G, 988H and 988K overlap in the field and the pump and bucket groups are not interchangeable.

Supply note: we supply aftermarket parts suitable for Caterpillar equipment, not genuine CAT parts. Part numbers are used for cross reference and identification only. Confirm against the machine serial number and the old part nameplate before ordering.

Frequently asked questions about CAT 988H parts

Is 385-0022 a complete pump assembly?

385-0022 is supplied as a complete pump assembly that cross references with 216-8978 on the 988H. Confirm with the machine serial number, since 988G and 988K use different pump groups.

Why does the loader lift slowly only when hot?

Cold oil masks a worn pump because viscosity is higher. Time the lift cycle at operating temperature and compare with the cold figure. A drop of more than twenty percent with high case drain flow confirms pump wear.

How often should the cooler be cleaned in Indonesia?

Every 250 hours during the wet season. Laterite fines mixed with rain set on the fins and block airflow permanently if left. Clean from the engine side with low pressure water.

The bucket does not empty cleanly and ore stays inside. Replace it?

Measure edge and bowl plate thickness first. If parent metal is sound, rebuild with wear plate and consider a low friction liner. Replace only when corner welds are cracked or the bowl is deformed.

Send the serial number, get fitment confirmed today

Aftermarket hydraulic, bucket, cylinder and cooling parts for CAT 988H loaders, in stock and shipped from Guangzhou.

Get price and stock
Scan the QR code to ask about CAT 988H parts on WhatsApp

WhatsApp +86 139 2519 9399 · Or message us directly: Chat on WhatsApp