CATParts Direct← Home
Home › Parts knowledge › D11R dozer parts

CAT D11R Dozer Parts: Seal Kit, Bushing and Bearing Wear List for African Mining Fleets

Short answer:The CAT D11R is a large track-type tractor in the 100 tonne class, a backbone machine in African open pit copper, coal and iron ore operations for ripping, push-loading and haul road maintenance. Four conditions drive its wear: continuous high load with heavy ripper shock, abrasive silica dust that penetrates every seal, long 20 to 35 day freight from China to Durban or Dar es Salaam, and remote sites where a single machine outage stalls a whole pit. The failure order is stable: undercarriage seals and bushings first (oil seepage, track sag, pin play), then bearings and cross shafts (noise, heat, driveline vibration), then relays and electrics (intermittent shutdown, dust in connectors). The expensive part is never the seal kit, it is a dozer down while trucks queue at the pit. Quote with the machine serial number and a photo of the old part plate - D11R and D11T share the frame but not every seal profile, bushing dimension and electrical connector.
Lip oil seal seal kit 124-2377 (CAT D11R Lip Oil Seal Seal Kit 124-2377 1242377 for Bulldozer)
Lip oil seal seal kit 124-2377 (CAT D11R Lip Oil Seal Seal Kit 124-2377 1242377 for Bulldozer)

Why the D11R loses undercarriage seals before it loses powertrain

Mining ripping is continuous shock load in abrasive dust. Silica fines work past wiper seals, mix with grease into a lapping paste, and grind the pin and bushing from the inside. The first symptom is usually oil seepage at the track links and growing pin play, not a loss of engine power.

The chain runs like this: dust ingress - wiper seal wear - grease contamination - pin and bushing scoring - track sag - roller and idler misalignment - accelerated undercarriage wear. On remote sites, a small seep is often ignored for weeks. A weekly walk-around measuring track sag is cheaper than one full undercarriage rebuild.

AreaSymptom on siteFree first checkUsual fix
Lip oil seal kitOil seepage at linksClean and mark the leak, measure sagNew seal kit, repack grease
Bushing sleevePin play, track sagMeasure pin to bushing clearanceNew bushings, turn pins
BearingNoise, heat at housingCheck end play and lube conditionNew bearing, flush lube
Cross shaftDriveline vibrationCheck spline wear and bolt torqueNew shaft, align
Relay switchIntermittent shutdownCheck connector for dust and pin fitNew relay, seal connector

Lip oil seal kit 124-2377 CAT D11R Lip Oil Seal Seal Kit 124-2377 1242377 for Bulldozer: mark the leak before tearing down

Order of work matters. Clean the area, mark the leak with chalk, run the machine for a shift and see exactly which link is seeping. A wet patch can travel along the rail, so replacing the wrong link is common. Seal kit 124-2377 CAT D11R Lip Oil Seal Seal Kit 124-2377 1242377 for Bulldozer is specified for D11R and D11T undercarriage - confirm the link pitch and seal profile, because early and late production runs differ.

When seals are replaced, repack with the correct grease, inspect the pin and bushing surfaces and check adjacent links. Fitting new seals onto scored pins pushes the same leak back within weeks.

Bushing sleeve 495-8292 (CAT D11T D11R Bushing Sleeve)
Bushing sleeve 495-8292 (CAT D11T D11R Bushing Sleeve)

Bushing sleeve 495-8292 CAT D11T D11R Bushing Sleeve: measure clearance, do not guess

Track sag and a clunk on direction change mean pin and bushing wear, but the fix depends on the measurement. Measure pin to bushing clearance and check whether pins can still be turned. Bushing 495-8292 CAT D11T D11R Bushing Sleeve is listed across D11R and D11T undercarriage, so match the inner diameter, length and the link it belongs to, not just the model name.

After fitting, turn pins where serviceable, torque the link bolts to spec and re-tension the track. Skipping track tensioning is the most common reason a fresh undercarriage wears unevenly.

Bearing 5P-1370 CAT D11R C32 C27 Bearing 5P-1370 for Engine: heat and end play are the hard signals

A failing bearing announces itself with rising housing temperature, growing end play and a rumble under load. Check lube condition for metal fines and measure end play cold and hot before ordering. Bearing 5P-1370 CAT D11R C32 C27 Bearing 5P-1370 for Engine is used in D11R engine and driveline positions - confirm the position and the housing bore, because the same number appears in more than one assembly.

When the bearing is replaced, flush the lube circuit, inspect the shaft journal and replace the related seals. A new bearing on contaminated oil fails quickly.

Engine and driveline bearing 5P-1370 (CAT D11R C32 C27 Bearing 5P-1370 for Engine)
Engine and driveline bearing 5P-1370 (CAT D11R C32 C27 Bearing 5P-1370 for Engine)

Cross shaft 106-0933 CAT 834K 988K D11R Cross Shaft 106-0933 1060933 for Wheel Loader Road Roller and relay switch 171-8708 CAT D11R 797 Relay Switch 171-8708 1718708 for Engine Excavator

Driveline vibration under load is often spline wear or loose flange bolts on the cross shaft, not a gearbox fault. Check spline backlash and bolt torque, and inspect the shaft for fretting. Shaft 106-0933 CAT 834K 988K D11R Cross Shaft 106-0933 1060933 for Wheel Loader Road Roller is shared with several large CAT machines - confirm the spline count and overall length before ordering.

Intermittent shutdown on a dusty pit is frequently a relay with dust in the connector or poor pin fit. Relay 171-8708 CAT D11R 797 Relay Switch 171-8708 1718708 for Engine Excavator replacement should include cleaning the socket, sealing the connector and re-routing the loom away from heat. A careful half hour here removes most repeat callouts.

Three rules for African mining D11R fleets

1) Weekly walk-around with a track sag measurement. Seepage caught early stays a seal kit, not a rebuild. 2) Repack grease and check tension after any undercarriage work. Dust plus loose track is the fastest way to lose a new set. 3) Keep a photo log of every old part plate. D11R and D11T share many numbers but not every dimension.

Follow these three and D11R undercarriage life stabilises. A mine measures cost per moved tonne, not the price of one seal kit.

Common spares and lead time reference

AreaTypical part numberSuggested stockLead time from China
Lip oil seal kit124-23772 per machine8 to 15 days
Bushing sleeve495-82921 set per 4 machines15 to 25 days
Bearing5P-13701 per 6 machines12 to 20 days
Cross shaft106-09331 per 8 machines15 to 25 days
Relay switch171-87081 per machine8 to 15 days

To Durban, Dar es Salaam and Walvis Bay: seals, relays and sensors go by air; bushings, bearings and shafts are cheaper by sea with inland trucking. Rainy season inland haulage slows sharply, so order downtime parts at least six weeks ahead.

Frequently asked questions (D11R African mining fleets)

Will D11R seal kits fit a D11T directly?

Not always. Link pitch and seal profile differ between early and late production runs. Send the machine serial number and a photo of the old part plate before we confirm.

Does track sag always mean a new bushing set?

No. Measure pin to bushing clearance and check if pins can still be turned. Sometimes turning pins and re-tensioning the track is enough for another season.

Why does a new bearing fail quickly?

Usually contaminated lube or a scored shaft journal. Flush the lube circuit, inspect the journal and replace related seals at the same time.

What causes intermittent shutdown on a dusty pit?

Often a relay with dust in the connector or poor pin fit. Clean the socket, seal the connector and re-route the loom away from heat when fitting the new relay.

Need D11R pricing and lead time for an African mining fleet?

Send the machine serial number and the part numbers you need. We reply within 24 hours with price, stock and air or sea timing to Durban, Dar es Salaam or Walvis Bay.

Check price and stock
WeChat / WhatsApp QR enquiry

WhatsApp +86 139 2519 9399 · Scan to add WhatsApp and send part numbers Send message