CATParts Direct← Home
Home › Parts Knowledge › D6R Dozer Parts

CAT D6R Dozer Parts - Undercarriage, Transmission and Cooling Wear List for Colombia and Ecuador

Short answer:The CAT D6R is a 20 tonne class tracked dozer used across Colombia and Ecuador in road building, Andean quarry benches, coal and limestone yards, and land development. Four hard conditions define the market: steep Andean gradients, high rainfall on the Pacific side, volcanic soil that is fine and abrasive, and long distances from the nearest dealer parts counter. Failure order is consistent: undercarriage wears first - track rollers, idler and bushings - showing as rising noise and a rough ride, then transmission and steering clutch behaviour changes under heat, then cooling capacity falls as the radiator packs with volcanic dust and mud. Always quote the machine serial number and arrangement number - D6R Series II and Series III differ in undercarriage and transmission parts.
Track roller 2544358 (2544358 Fuel Injection C7 C9 C-9 Impulse Pump Compatible wit) for CAT D6R dozer undercarriage
Track roller 2544358 (2544358 Fuel Injection C7 C9 C-9 Impulse Pump Compatible wit) for CAT D6R dozer undercarriage

Undercarriage is the first bill on an Andean dozer

On a dozer the undercarriage is the largest running cost, and in Colombia and Ecuador it wears faster than the book suggests. Steep gradients load the idler and the front rollers unevenly, and volcanic soil is fine enough to pass a tired seal and abrasive enough to grind the bushing.

The failure chain is easy to follow: seal leaks, grease escapes, abrasive enters, bushing wears oval, track pitch stretches, the chain starts to ride high on the sprocket, and the whole assembly wears faster. By the time the operator complains about noise, the sprocket is usually already damaged.

AreaSymptom on siteFirst check (no cost)Usual action
Track roller / idlerNoise, rough ride, oil weepingCheck for play and leaking sealsReplace roller or idler
Track chain and bushingsPitch stretch, sprocket jumpMeasure pitch over five linksReplace chain or turn pins
Transmission / steeringSlow steer, harsh shift, heatCheck pressures and oil conditionAdjust or repair clutch packs
Radiator / coolingOverheat on sustained pushLook through fins, check fan driveClean or replace core
Blade and cutting edgesPoor penetration, worn moldboardMeasure edge heightReplace or reverse edges

Rollers and idlers 2544358 2544358 Fuel Injection C7 C9 C-9 Impulse Pump Compatible wit - measure play, not noise

Noise is the last symptom. Check vertical play in each roller and the idler, and look for oil weeping at the seal. A roller with play but no leak will still fail, because the bearing race is already damaged. Replace on measurement, and replace in sets across the same side - one new roller beside four worn ones simply carries more load and fails early.

On volcanic soil, also check the roller guard and the seal area for packed dirt. Packed material holds moisture against the seal and accelerates corrosion pitting.

Track chain assembly 457-4643 (Applicable to Caterpillar D6R III D6T D7R Bulldozer Lever Co) for CAT D6R dozer
Track chain assembly 457-4643 (Applicable to Caterpillar D6R III D6T D7R Bulldozer Lever Co) for CAT D6R dozer

Track chain 457-4643 Applicable to Caterpillar D6R III D6T D7R Bulldozer Lever Co - pitch decides the whole bill

Measure pitch across five links and compare with the service limit. Within limit: turn pins and bushings if the wear is still in the turnable range. Over limit: replace the chain. Fitting a new chain on a worn sprocket wears the new chain quickly, and fitting a new sprocket on a stretched chain does the same in reverse.

The cheapest intervention is correct track tension. Too tight destroys bushings and sprockets, too loose causes impacts and cracked links. Check tension at the start of every shift on steep ground, because a chain that is correct on the flat can be too loose on a grade.

Transmission and steering 1620324 Suitable for Caterpillar D6R Bulldozer Hydraulic Pump-Part N - heat is the first suspect

Slow steering, harsh shifts and a transmission that slips when hot usually share one cause: oil temperature. On Andean grades the dozer spends long periods at full load at low ground speed, which is the worst case for a powershift transmission.

Check in this order: oil level and colour, suction screen for clutch material, main pressure, and cooler flow. Milky oil means water ingress, burnt smell means the friction modifiers are gone, and clutch material on the screen means a pack is failing and the machine should be planned out of service.

Radiator core 1620324 (Suitable for Caterpillar D6R Bulldozer Hydraulic Pump-Part N) for CAT D6R dozer cooling system
Radiator core 1620324 (Suitable for Caterpillar D6R Bulldozer Hydraulic Pump-Part N) for CAT D6R dozer cooling system

Cooling 3878581 For Caterpillar D6r Bulldozer C9 Engine Assembly 3878581 387 - volcanic dust packs the core

Volcanic dust is finer than quarry dust and it mixes with rain to form a layer that hardens on the fins. Clean the radiator weekly from the inside out at low pressure, and inspect with a light behind the core rather than from the front. Replace the core when a clean core still cannot hold temperature at rated load.

Check the fan drive, belt tension and the shroud seals at the same time. A missing shroud seal can cost more cooling capacity than a partially blocked core.

Blade and edges 1181608 Suitable for Cat 1181608 D6R D8N Track Bottom Roller D4D D5 - the grading cost nobody tracks

Worn cutting edges and a rounded moldboard cost fuel every hour, because the operator pushes harder for the same cut. Measure edge height every 250 hours and use reversible edges where the design allows. On road building work, a straight, sharp edge produces a better grade in fewer passes, which pays back faster than most operators expect.

Common parts and lead times

AreaTypical part numberSensible stockLead time from China
Track roller25443581 set per 4 machines20 to 35 days by sea
Track chain assembly457-46431 per 6 machines30 to 45 days by sea
Transmission parts kit16203241 kit per 6 machines10 to 18 days
Radiator core38785811 per 8 machines15 to 25 days
Cutting edge11816082 per machine10 to 18 days

For Buenaventura, Cartagena, Guayaquil and Manta, sea freight is the default for undercarriage and air freight only for urgent transmission parts. Plan undercarriage as an annual budget line, because on a dozer it is not a repair, it is a consumable.

FAQ - CAT D6R in Colombia and Ecuador

When should a D6R track chain be replaced?

When measured pitch across five links exceeds the service limit. Before that, pins and bushings can be turned if the wear is still in the turnable range. A new chain on a worn sprocket wears out quickly, so check the sprocket at the same time.

Why does the transmission slip only when hot?

Heat thins the oil and reduces clutch pack grip. Check oil condition, the suction screen for friction material, main pressure and cooler flow. Burnt oil means the friction modifiers are gone and a rebuild is likely.

Is it acceptable to replace a single track roller?

It is better to replace rollers in sets on the same side. A single new roller next to worn ones carries more load and fails early, so the total cost goes up rather than down.

How do I know the radiator needs replacing rather than cleaning?

If a properly cleaned core still cannot hold temperature at rated load, the core is restricted internally. Check the shroud seals and fan drive before condemning the core.

Need a quote and lead time for D6R parts?

Send the machine serial number and arrangement number with the part numbers you need. We reply within 24 hours with price, stock and shipping options to Colombia and Ecuador.

Check price and stock
Scan to enquire on WhatsApp

WhatsApp +86 139 2519 9399 · Scan and send part numbers directly on WhatsApp Send a message