CATParts Direct← Home
Home › Parts Knowledge › D9N Dozer Parts

CAT D9N Dozer Parts - Undercarriage, Final Drive and Blade Wear List for Brazil and Argentina

Short answer:The CAT D9N is a 38 tonne class dozer, a veteran on Brazilian sugar cane land clearing, Mato Grosso farm development and Argentine quarry and road work. Four hard conditions define this market: wet season mud that packs tracks, dry season dust, mixed cane and quarry duty with full blade loads, and parts moving into Santos or Buenos Aires in 15 to 30 days. Failure order is consistent: undercarriage rollers and chains wear first on mud and dust, then final drives seep and one track loses push, then cutting edges blunt and the blade stops biting. Always quote the machine serial number - D9N and D9N XL carry different undercarriage and blade fitments.
Track roller and undercarriage part 106-7438 (CAT D9N D9R Clutch Plate Friction Disc Friction Plate 106-74) for CAT D9N dozer
Track roller and undercarriage part 106-7438 (CAT D9N D9R Clutch Plate Friction Disc Friction Plate 106-74) for CAT D9N dozer

Cane land and quarry duty set the failure order

Brazilian cane clearing and Argentine quarry work share one pattern: the dozer works at full blade load on ground that alternates between adhesive mud and abrasive dust. Every track joint flexes through packed mud that dries like mortar, and every roller seal fights silica dust.

The failure chain is steady: mud and dust defeat the roller face seals, bearings wear, one roller sinks and the load shifts onto its neighbours, chain pitch stretches, the sprocket jumps teeth. On the powertrain side, full push loads age the final drive seals, oil seeps, level drops, and the planetary set runs toward failure.

AreaSymptom on siteFirst check (no cost)Usual action
Track rollersLeaking, flat spots, noiseInspect seal leakage and wearReplace rollers as a set per side
Chains and shoesPitch stretch, jumpingMeasure pitch and grousersReplace chain and shoes
Final driveOne track weak, seepageDrain oil, check for metalReplace seals or assembly
Blade / cutting edgeBlade rides up, spillsMeasure edge thicknessReplace edge and end bits
Track adjusterLoose track, daily greaseCheck cylinder leak downReplace seals or unit

Rollers and chains 106-7438 CAT D9N D9R Clutch Plate Friction Disc Friction Plate 106-74 - mud sets the rules

Inspect in a fixed order: seal leakage first, then roller tread and flange wear, then pitch stretch and grouser height. A leaking roller in cane mud is a countdown, not a maintenance item - grit enters the bearing and the wear accelerates by the week.

Replace strategy is simple and non negotiable: rollers as a full set per side, chains and shoes together when pitch exceeds the wear limit. Mixing new rollers into a stretched chain transfers the entire load into the new parts. Wash the tracks every shift in the wet season - dried mud on a track is mortar grinding every joint.

Final drive seal and component 6T-9651 (CAT D9N D10N Hydraulic Pump Gear Pump Piston 6T-9651 for Bul) for CAT D9N powertrain
Final drive seal and component 6T-9651 (CAT D9N D10N Hydraulic Pump Gear Pump Piston 6T-9651 for Bul) for CAT D9N powertrain

Final drive 6T-9651 CAT D9N D10N Hydraulic Pump Gear Pump Piston 6T-9651 for Bul - the drain plug tells the truth

Before a single bolt comes out, drain a sample from the final drive after the machine sits half an hour: metal flakes or black oil mean the planetary set or bearings are already wearing. Continuing to push with flakes in the oil turns a seal job into a complete final drive, sprocket and chain replacement.

Separate three complaints before teardown: final drive internal wear (weak push, drain sample dirty), steering clutch slip (one side heats and smells), and low oil level from seepage (top up and find the leak). Only confirmed final drive symptoms justify pulling the assembly.

Blade and cutting edge 8E-4196 CAT D9N D9R End Bit 8E-4196 8E-4197 for Bulldozer - a blunt edge bills the powertrain

A cutting edge worn past a third of its section stops penetrating - the operator compensates with throttle, and the heat bill lands on the torque converter, the final drives and the undercarriage at the same time. Replace edges at measured wear, always in pairs, with new bolts torqued diagonally.

End bits and corner bits carry the side load on cane roots and quarry faces - replace them with the edge, never after. Old bolts re used on a blade are the cheapest way to strip a bolt hole in a blade worth a hundred times more.

Cutting edge and blade wear part 8E-4196 (CAT D9N D9R End Bit 8E-4196 8E-4197 for Bulldozer) for CAT D9N dozer blade
Cutting edge and blade wear part 8E-4196 (CAT D9N D9R End Bit 8E-4196 8E-4197 for Bulldozer) for CAT D9N dozer blade

Track adjuster and hardware 6E-4835 CAT D9N Hydraulic Cylinder 6E-4835 for Bulldozer - wet season discipline

A track that needs greasing daily is telling you the adjuster seal has failed. Charge the adjuster, mark the rod, and check the mark next shift - movement means the seal is gone. In the wet season run tracks at the looser end of specification: over tightened tracks in mud shock the idlers and front idler brackets on every direction change.

Consumables and planning 6E-4836 CAT D9N Hydraulic Cylinder 6E-4836 for Bulldozer - the shelf beats the emergency

The standard South American fleet practice: one full set of edge hardware and roller face seals per dozer on the shelf, and a quarterly oil sample from each final drive. These parts cost a fraction of one day of downtime, and the samples catch seepage months before a failure.

Buy blades and undercarriage against measured wear in the dry season, when transit and site access are both at their best.

Common parts and lead times

AreaTypical part numberSensible stockLead time from China
Track roller set106-74381 set per 6 dozers15 to 25 days
Final drive seals / parts6T-96511 kit per dozer15 to 30 days
Cutting edge / end bits8E-41962 sets per dozer12 to 20 days
Adjuster / track hardware6E-48351 set per dozer12 to 20 days
Face seals / consumables6E-4836Full kit per dozer10 to 15 days

For Mato Grosso, Sao Paulo state and the Argentine littoral, sea freight into Santos or Buenos Aires carries undercarriage and blade structure at the best cost; face seals and edge hardware move by air into Guarulhos or Ezeiza. Order before the wet season - December to March doubles both transit times and site access problems.

FAQ - D9N in Brazil and Argentina

Do D9N and D9N XL share undercarriage parts?

No. The XL variant runs a longer track frame with more rollers and a different chain. Confirm with the machine serial number and old part photos before ordering.

A roller is leaking - can I just watch it?

Not in cane mud. Grit enters through the failed face seal and wear accelerates weekly. Schedule a full set replacement per side; single roller swaps shift the load into the new part.

How do I judge final drive health without teardown?

Drain a sample after the machine sits half an hour. Metal flakes or black oil mean internal wear; water or milk colored oil means a breached seal. Order parts against the sample, not the noise.

When does a cutting edge need replacement?

At one third section loss, always in pairs with new bolts. A blunt edge rides up, the operator adds throttle, and the cost lands on the torque converter and final drives.

Need a quote and lead time for D9N parts?

Send the machine serial number and part numbers. We reply within 24 hours with price, stock and sea or air transit time to Santos, Guarulhos or Buenos Aires.

Check price and stock
Scan to enquire on WhatsApp

WhatsApp +86 139 2519 9399 · Scan and send part numbers directly on WhatsApp Send a message