CATParts Direct← Home
Home › Parts Knowledge › D9T / D10T Dozer Parts

CAT D9T / D10T Dozer Parts - Undercarriage, Track and C15 Engine Wear List for Southern Africa

Short answer: D9T and D10T dozers carry production dozing and ripping on the Zambian and Katangan copperbelt and on Mozambican coal haul roads. The wear order rarely changes: track rollers and bottom rollers go first, then track shoes and bushings follow, then roller covers split and let abrasive fines into the roller, and the C15 engine shows cylinder liner wear once hours build. Read four things on site: roller seal leakage, shoe height against specification, track sag and bushing play, and coolant condition. Send the machine serial number, because D9T, D9R and D10T undercarriages share the dozer family but not every part number.
CAT D9T D9R double flange track roller 196-9954
Double flange track roller 196-9954 for Caterpillar D9T, D9R and D9GC dozers

Why Southern African dozing eats undercarriages

Copperbelt and coal basin duty shares three traits: abrasive laterite and sandstone fines that pack into every moving joint, long pushes at high blade load, and long intervals between workshop visits. On D9T and D10T machines the undercarriage absorbs almost all of that abuse, and the engine pays the second bill through cooling load.

The chain is simple and expensive: seal leakage lets fines into the roller, the roller loses its rolling surface and starts skidding, skidding wears the shoe and link faces flat, and the extra rolling resistance loads the powertrain and pushes coolant temperatures up. Fleets that replace rollers on schedule spend far less than fleets that wait for a visible failure.

AreaField symptomFirst free checkUsual action
Track rollersLeakage, flat spots, skiddingLook for oil streaks and check rotationReplace roller 196-9954
Bottom rollersUneven wear across the frameMeasure flange wear and rotationReplace roller 332-6423
Track shoesLow grouser height, bent shoesMeasure height against specificationReplace shoes 571-3544
Roller coversCracked cap, dirt ingressVisual check after washingReplace cover 131-1650
C15 engineCoolant loss, blow byCoolant test and crankcase pressureReplace liner 523-8663

Track rollers 196-9954 and 332-6423

196-9954 is the double flange track roller for D9T, D9R and D9GC dozers. 332-6423 is the bottom roller for D10, D10T and D10T2 machines. Both fail the same way and both give a free warning before they fail.

The warning is oil. Wash the roller frame and look for streaks after one shift; a weeping seal is visible long before it runs dry. Then check whether the roller still turns freely with the track tension relieved, since a seized roller starts flat spotting immediately. Replace in sets across the position rather than singly, because a fresh roller next to worn neighbours takes an overload and fails early.

CAT D9R D9T track shoe assembly 571-3544
Track shoe assembly 571-3544 for Caterpillar D9R and D9T dozers

Track shoes 571-3544 and roller covers 131-1650

571-3544 is the track shoe assembly for D9R and D9T. Shoe replacement is a measurement decision: record grouser height against the wear limit and look for bent plates at the chain ends. Running shoes past the limit is expensive in a specific way, because worn shoes accelerate link and bushing wear, so the chain becomes the next bill.

131-1650 is the track roller cover used on D10N, D10R and D10T crawler dozers. It is a cheap part that protects an expensive one. A cracked cover lets abrasive fines straight into the roller, so if a cover is missing after a rock strike, fit a new one the same day rather than at the next service.

C15 cylinder liner 523-8663

523-8663 is the C15 engine cylinder block liner shared by D8T, D9T, R1600 and R1700 applications. On high hour dozers it is usually coolant condition that decides liner life, not hours alone.

Check three things before condemning the engine: coolant condition and nitrite level, because liner pitting starts where the inhibitor is exhausted; crankcase pressure, which separates liner and ring wear from injector trouble; and coolant loss with no external leak. When the liner is replaced, fit new seals, check the block counterbore for damage, and look for the reason the inhibitor died rather than only treating the symptom.

CAT C15 cylinder block liner 523-8663
C15 cylinder block liner 523-8663 for Caterpillar D8T, D9T, R1600 and R1700 applications

Undercarriage habits that cut cost per hour

Three habits do most of the work. Check track sag every shift; too tight multiplies roller and link wear, too loose damages shoes and guides. Wash the undercarriage where the machine works in abrasive fines, because packed material holds moisture against seals. Turn pins and bushings at the interval the manual gives, since a turned chain can double the remaining link life for the cost of a workshop visit.

Record wear measurements rather than relying on appearance. A roller that looks acceptable can already be below spec, and a written trend tells you which machines need the next budget.

Delivery, documents and packing to Southern Africa

Stock items leave the same day and reach Lusaka, Kitwe, Lubumbashi and Maputo in roughly 6 to 10 working days by air or road express. Rollers, shoes and liners move best as sea LCL lots against Durban, Walvis Bay or Beira depending on destination. Export packing uses heat treated pallets or wooden cases, with machined faces protected and a packing list, part photos and loading video before dispatch.

A quote needs three things: machine serial number photo, old part nameplate photo, and the position on the machine.

Frequently asked questions

Do D9T and D10T share undercarriage parts?

Partly. Roller 196-9954 covers D9T, D9R and D9GC, while bottom roller 332-6423 covers D10, D10T and D10T2, and cover 131-1650 covers D10N, D10R and D10T. Always match the serial number before ordering, because track gauge and roller design changed across production years.

When is a track roller finished rather than just dirty?

Wash the frame and look for oil streaks after one shift, then check whether the roller turns freely with track tension relieved. Streaking plus a roller that drags means the seal is gone and the rolling surface will flat spot quickly, so replace it before the flanges damage the link.

Can I replace one roller instead of a set?

You can, but the new roller then carries more than its share next to worn neighbours and usually fails early. Replacing all rollers in a position and checking the shoe and link condition at the same time gives the lowest cost per hour.

How long does delivery to Zambia or the DRC take?

Stock parts ship the same day and reach Lusaka, Kitwe and Lubumbashi in about 6 to 10 working days by air or road express. Rollers and shoes move as sea LCL lots against Durban, Walvis Bay or Beira, with packing list and loading photos before departure.

Need a quote for D9T / D10T dozer parts?

Send the machine serial number and old part photos. Fitment confirmed and stock reserved the same day.

Request a quote
WhatsApp QR code

WhatsApp +86 139 2519 9399 · Scan to send a part number, or open the chat